Factory Service Manual For New Holland 975 Combine. Manual Contains Illustrations, Instructions, Diagrams For Step By Step Remove And Install, Assembly And Disassembly, Service, Inspection, Repair, Troubleshooting, Tune-Ups.
Format: PDF
Language: English
Pages: 282
Number: 40097510
Bookmarks: Yes
Wiring Diagrams: Yes
Model
New Holland Combine
975
Contents
-INTRODUCTION
-SPECIFICATIONS
-STEERING PLATFORM
Removal Of The Ground Speed Vari-Drive, Reel And Header Control Levers.
Removal Of The Engine “Stop Knob”, Throttle And Gear Shift Selectors
Removal Of The Concave Adjustment Control Lever, Reel Vari-Drive And Drum Vari-Drive Control Levers
Removal Of Brake And Clutch Pedals, And Parking Brake Handle
Disassembly Of Threshing Mechanism, Header And Unloading Auger Engagement Levers
-STEERING AND REAR AXLE
Removal Of The Steering Valve
Replacement Of A King Pin And Axle Bushings
Replacement Of Rear Axle Pivot Bushings
Steering Cylinder Adjustments
-GROUND SPEED VARIATOR
Removal Of Ground Speed Variator
Disassembly Of Suspension Fork
Dismantling Of Ground Speed Variator
Assembly Of Ground Speed Variator
Replacement Of Suspension Fork
Adjustment Of Ground Speed Variator And Belt Tension
-BRAKES AND PARKING BRAKE
Removal And Replacement Of A Brake
Adjustment Of Brakes
Parking Brake
-CLUTCH AND GEARBOX
Removal Assembly And Adjustment Of The Clutch
Replacement Of The Clutch Bearings
Replacement Of The Drive Shaft Oil Seal
Disassembly And Reassembly Of The Differential And Gears
Replacement Of The Gear Selection Locking Device
Selector Shaft Bushings
Removal And Replacement Of The Gear Pinions
Replacement Of Half Shaft Bearings
Replacement Of A Wheel Hub
Replacement Of A Half Shaft
-WHEELS AND TYRES
Standard Sizes
Tightening Of Wheel Nuts
Traction Wheels Track Width
-HYDRAULIC EQUIPMENT
Hydraulic Pump
Tank With Filter
Treble Master Valve And Relief Valve
Steering Valve With Seals
Header Lift Rams
Steering Ram
Traction Variator Ram
-ELECTRICAL EQUIPMENT
Wiring Diagram And Electrical Equipment For Petrol Engine.
Wiring Diagram And Electrical Equipment For Diesel Engine
-ACCESSORIES FOR ENGINE, POWER BAND TENSIONER AND UNLOADING AUGER CLUTCH
Removal Of The Main Engine Driven Shaft And Housing
Dismantling And Assembly Of The Driven Shaft Replacement Of The Engine Driven Shaft Housing Removal And Replacement Of The Radiator Petrol Engine
Removal And Replacement Of The Air Filter Dismantling And Assembly Of Rotary Screen Removal And Replacement Of The Petrol Engine Refitting And Adjusting Of The Throttle, Petrol Engine Up To Series 140
Removal And Replacement Of The Unloading Auger Drive Belt Tension Pulley Assembly.
Removal And Replacement Of The Main Drive Tension Pulley Assembly.
Adjusting Of The Throttle Petrol Engine From Series 140 Onwards.
Removal And Replacement Of The Diesel Engine Driven Shaft And Housing
Removal And Replacement Of The Radiator Diesel Engine
Removal And Replacement Of The Diesel Engine Adjustment Of The Throttle Diesel Engine
-REMOVAL AND ATTACHMENT OF HEADER AND STRAW ELEVATOR
Removal And Connection Of The Header With Strawelevator From And To The Machine.
Leveling Of The Header.
Removal And Connection Of The Header From And To The Strawelevator.
-KNIFE AND KNIFE DRIVE
Removal Of Knife And Knife Drive
Reassembly And Adjustment Of The Knife And Knife Drive.
-FEEDING AUGER
Removal And Replacement Of The Feed Auger
Removal Of Eccentric
Removal And Replacement Of Centre Shaft
Replacement Of Eccentric Shaft
Replacement Of Finger Guides
-REEL AND VARIABLE REEL DRIVE
Removal Of The Reel
Removal And Replacement Of The Eccentric
Removal And Replacement Of A Reel Finger And Reel Bar
Bat Reel
Removal And Replacement Of The Reel Arms
Removal Of The Reel Vari-Drive Belt
Removal And Replacement Of The Upper Vari-Drives Sheaves
Removal And Replacement Of Knife Drive Intermediate Shaft And Lower Vari-Drive Sheaves
Adjustments On The Reel Variator
-STRAW ELEVATOR, TOP AND LOWER SHAFT
Removal And Replacement Of The Straw Elevator Bottom Shaft
Removal Of The Straw Elevator Upper Shaft
Reassembling Of The Straw Elevator Upper Shaft
Removal And Replacement Of The Intermediate Plate In The Straw Elevator
-SLIP CLUTCHES ON HEADER
Removing And Replacing The Slip Clutch On The Intake Auger
Removing And Replacing The Slip Clutch On The Top Straw Elevator Shaft
Wear Plates Underneath The Cutterbar
-DRUM AND REVOLUTION COUNTER, CONCAVE WITH STONE TRAP
Removal And Replacement Of The Drum
Drum Rasp Bar Replacement
Removing And Replacement Stone Trap And Concave
Concave Adjustments
Revolution Counter On Drum Shaft
-BEATER
Removal Of The Beater Shaft
Removal And Reassembling Of The Beater
Replacement Of The Beater Shaft
-DRUM AND BEATER SPEED VARIATOR
Removal Of The Variator Belt
Installing The Variator Belt
Adjusting The Variator
-MAINSHAFT
Removal Of The Main Shaft
Replacement Of The Main Shaft
-ECCENTRIC SHAFT
Disassembly Of The Eccentric Shaft And Drive Rods
Assembly Of The Bearing Into The Drive Rod
Replacement Of The Eccentric Shaft And Drive Rods
-COLLECTING PAN AND SHAKER SHOE
Removal And Replacement Of The Shaker Shoe
Removal And Replacement Of The Collecting Pan
-STRAWWALKERS, STRAWWALKER SHAFTS AND CURTAIN BEHIND BEATER
Removal Of The Straw Walkers Shafts
Replacement Of A Sealed Ball Bearing On A Straw Walker Shaft
Installing The Straw Walkers And Shafts
Removing And Replacement Of The Curtain Behind The Beater
-FAN
Removal And Replacement Of The Fanning Mill, Shaft And Housing Cover
Adjustable Wind Deflectors
Removal And Replacement Of The Fan Variator
Variator Adjustments
-GRAIN AND TAILINDS ELEVATORS WITH AUGERS
Removal And Replacement Of Tailings Elevator Chain
Removal And Replacement Of The Tailings Elevator And Auger
Removal And Replacement Of The Top Shaft Of The Tailings Elevator
Removal And Replacement Of The Tailings- Or Grain Auger
Removal And Replacement Of The Top Tailings Auger
Removal And Replacement Of The Intermediate Drive Shaft For Tailings Elevator
Removal And Replacement Of The Grain Elevator Chain
Removal And Replacement Of The Grain Elevator
-GRAINTANK AND UNLOADING SYSTEM
Removal Of Unloading Tube And Auger
Removal Of The Unloading Auger
Replacement And Adjustments Of The Unloading Tube And Auger
Removal Of The Graintank Auger
Removal Of The Bearing On The Right
Reinstalling Of The Bearing And Graintank Auger Replacement Of The Universal Joint And Bushing
Removal And Replacement Of The Intermediate Shaft
-SPECIAL TOOLS
What you get
You will receive PDF file with high-quality manual on your email immediately after the payment.
Reviews
There are no reviews yet